Will you solve all these problems when using the

by:Jiali     2020-06-06
We all know that after using the chain saw for a long time, we will encounter various problems, such as the chain saw can't go down or the tree can't be sawed, the carburetor does not absorb oil, and the throttle can't be added. Will you solve all these problems? Below we will give you an analysis. 1. The blade of the chain saw is fast but the saw can't go down? Sharpness of the blade is only a condition. The teeth should be staggered to each other and slightly offset in different directions, so that the front saw seam will not affect the feed of the rear blade. Otherwise, the saw gap is too narrow, it will catch the blade behind, and you will not be able to saw. 2. What is the reason why the chain saw does not enter the tree? See if there is any curling edge on the chain saw blade, and evenly file it. Then there may be problems with the chain file of the chain saw. If you are a novice, be sure to file the sharpest corner of the chain when filing the chain, then there will be no sawing and no sawing. Biased. 3. How does the oil pump of the chain saw work? The working principle of the oil pump of the chain saw machine: the worm rod drives the turbine to rotate, and the principle of volume ratio is used to form a negative pressure in the oil tank. Under the action of atmospheric pressure, the oil is pressed into the oil pipe and sent to the guide plate and the chain. The oil pump assembly of the chain saw is a large part of the lubrication system of the two-stroke chain saw. It provides oil to the high-speed chains and guide plates to prevent excessive heat from friction during operation, which causes the chain guide of the chain saw to be too high and reduce Work efficiency. The lubricating task of the chain saw engine is completed by the two-stroke oil in the fuel. 4. What is wrong with the oil absorption of the chain saw carburetor? See if the filter head in the fuel tank is too dirty, and change it if it doesn't work; determine whether the fuel pipe is rotten; check whether the carburetor is too dirty, or if the carburetor is not adjusted properly, try to loosen the L needle ; It is also possible that the check valve on the fuel tank is broken. 5. What should I do if the chain saw can't afford the throttle? 1. The carburetor is not adjusted properly or the carburetor is blocked, and the carburetor is damaged, resulting in the ineffective production of mixed oil and gas; 2. The oil circuit is blocked or leaking, resulting in insufficient oil supply; 3. Air filter is blocked, resulting in insufficient gas supply; 4. The cylinder or piston is worn out and must be replaced in its entirety; 5. Poor oil quality or improper blending ratio, resulting in insufficient combustion; 6. It is also possible that the damper of the chain saw is not opened or fully opened. 6. The chain saw engine works normally, but what happens if the saw teeth do not turn? 1. Open the safety lock, pull the baffle located in front of the handle back to the handle position, if you hear a 'click', it will open, otherwise, the chain will be locked by pushing forward, and the throttle chain will not move as long as the engine is added. 2. The pitch of the chain is different from that of the sprocket. 3. The chain teeth and the guide rail are too tightly locked, remove the guide plate and the chain, and place the chain on the chain saw guide plate to see if it can be pulled by hand. If the above inspection fails, please find a professional to help. Today I told you that the blade of the chain saw is fast but the saw cannot go down, the chain saw does not enter the tree, the chain saw carburetor does not absorb oil, the chain saw cannot increase the throttle, and the working principle of the oil pump of the chain saw. Good understanding of chain saw, better use of chain saw.
Finding a reliable solution for the bicycle gas engine kit manufacturers bicycle engine kit suppliers not only supports operation of the entire system but also enhance the beauty of your workplace.
To reduce your production costs, get your and bicycle engine kit suppliers from Nantong Jiali Mechanical and Electrical Equipment Factory,you will get high quality warranty at favorable price in return. Visit Jiali Bicycle Engine.
Nantong Jiali Mechanical and Electrical Equipment Factory has a number of producing line for producing bicycle gas engine kit manufacturers.
give you an additional bicycle engine kit suppliers option for your bicycle engine kit suppliers, whether it being a bicycle engine kit suppliers, bicycle engine kit suppliers or bicycle engine kit suppliers. Go and get more info at Jiali Bicycle Engine.
Nantong Jiali Mechanical and Electrical Equipment Factory attach great importance to the quality of our products and R&D services.
Custom message
Contact